source: buchla-68k/orig/DOC/GLCFNS.TXT@ 4aad7a7

Last change on this file since 4aad7a7 was 3ae31e9, checked in by Thomas Lopatic <thomas@…>, 7 years ago

Imported original source code.
  • Property mode set to 100755
File size: 5.1 KB
Line 
1Drivers for the Epson Graphic LCD Controller (GLC) chip
2-------------------------------------------------------
3
4Document: glcfns.doc Version 3 1988-08-03
5
6Based on: glcinit.c Version 5 1988-08-03
7 glcdefs.h Version 3 1988-08-03
8 glcplot.s Version 2 1987-04-23
9
10--------------------------------------------------------------------------------
11
12
13GLC Function synopsis:
14----------------------
15
16GLCcrc unsigned GLCcrc(row, col)
17GLCcurs void GLCcurs(crs)
18GLCcxy unsigned GLCcxy(x, y)
19GLCdisp void GLCdisp(dsp, crs, blk1, blk2, blk3)
20GLCinit void GLCinit()
21GLCplot void GLCplot(x, y, val)
22GLCtext void GLCtext(row, col, s)
23GLCwrts void GLCwrts(s)
24
25
26GLC Variable synopsis:
27----------------------
28
29lcdbase unsigned lcdbase; LCD graphics base address
30lcdbit unsigned lcdbit; LCD graphics pixel bit mask
31lcdcol unsigned lcdcol; LCD text column
32lcdctl1 unsigned lcdctl1; LCD display control -- command
33lcdctl2 unsigned lcdctl2; LCD display control -- data
34lcdcurs unsigned lcdcurs; LCD graphics pixel byte address
35lcdrow unsigned lcdrow; LCD text row
36lcdx unsigned lcdx; LCD graphics x
37lcdy unsigned lcdy; LCD graphics y
38
39
40GLC Constants:
41--------------
42
43#define G_INIT (char)0x40 initialize GLC
44#define G_MWRITE (char)0x42 set memory write mode
45#define G_MREAD (char)0x43 set memory read mode
46#define G_SETSAD (char)0x44 set scroll addresses
47#define G_CRSWR (char)0x46 write cursor address
48#define G_CRSRD (char)0x47 read cursor address
49#define G_CRSMRT (char)0x4C set cursor direction - right
50#define G_CRSMLT (char)0x4D set cursor direction - left
51#define G_CRSMUP (char)0x4E set cursor direction - up
52#define G_CRSMDN (char)0x4F set cursor direction - down
53#define G_ERASE (char)0x52 erase
54#define G_SLEEP (char)0x53 set sleep mode
55#define G_DSPCTL (char)0x58 set display controls
56#define G_HSCRL (char)0x5A set horizontal dot scroll
57#define G_OVRLAY (char)0x5B set overlay mode
58#define G_CGRAM (char)0x5C set CG RAM base
59#define G_CRSFRM (char)0x5D set cursor format
60
61#define LCD_WC lcd_a1 write command address
62#define LCD_RS lcd_a0 read status address
63#define LCD_WD lcd_a0 write data address
64#define LCD_RD lcd_a1 read data address
65
66#define G_PLANE1 (unsigned)0x0000 plane 1 base address
67#define G_PLANE2 (unsigned)0x2000 plane 2 base address
68
69#define G_OFF 0 off
70#define G_ON 1 on
71#define G_B2 2 blink - FR/32
72#define G_B1 3 blink - FR/64
73
74GLC characteristics:
75--------------------
76
77 Graphics:
78
79 510 pixels wide by 64 pixels high.
80 Graphics are in plane 2.
81 X = 0, Y = 0 is the lower left corner of the display.
82
83 Text:
84
85 8 rows by 85 columns
86 Text is in plane 1.
87 Row 0, Column 0 is the upper left corner of the display.
88
89 Characters:
90
91 Internal ASCII character generator.
92 5 pixels wide by 7 pixels high, in a 6 by 8 block.
93
94G_INIT parameters:
95------------------
96
97 0x12 P1 IV, M/S, W/S, M2, M1, M0
98 0x05 P2 WF, FX
99 0x07 P3 FY
100 0x54 P4 C/R
101 0x58 P5 TC/R
102 0x3F P6 L/F
103 0x55 P7 APL
104 0x00 P8 APH
105
106G_SETSAD parameters:
107--------------------
108
109 0x00 P1 SAD1L
110 0x00 P2 SAD1H
111 0x3F P3 SL1
112 0x00 P4 SAD2L
113 0x20 P5 SAD2H
114 0x3F P6 SL2
115 0x00 P7 SAD3L
116 0x00 P8 SAD3H
117
118
119GLC initialization values:
120--------------------------
121
122 G_INIT:
123 -------
124
125 IV 0 correct screen to top line
126 M/S 1 master mode
127 W/S 0 single screen drive
128 M2 0 8 pixel wide CG
129 M1 0 32 character CG RAM area
130 M0 0 internal CG
131
132 WF 0 "line reversion" drive
133 FX 0x05 6 pixel character block width
134
135 FY 0x07 8 pixel character block height
136
137 C/R 0x54 85 characters per line
138
139 TC/R 0x58 89 scan times per line
140
141 L/F 0x3F 64 lines
142
143 APL,APH 0x0055 virtual screen size = 85 characters
144
145
146 G_SETSAD:
147 ---------
148
149 SAD1 0x0000 plane 1 (text plane) address = 0x0000
150
151 SL1 0x3F plane 1 height = 64 lines
152
153 SAD2 0x2000 plane 2 (graphics plane) address = 0x2000
154
155 SL2 0x3F plane 2 height = 64 lines
156
157Functions:
158----------
159
160 unsigned
161 GLCcrc(row, col)
162 unsigned row, col;
163
164 Positions the GLC cursor at ('row', 'col') preparatory
165 to writing text. Returns the calculated cursor address.
166
167 GLCcurs(crs)
168 short crs;
169
170 Turns the cursor on or off.
171
172 unsigned
173 GLCcxy(x, y)
174 unsigned x, y;
175
176 Positions the GLC cursor at ('x', 'y') preparatory to
177 writing graphics. Returns a bit mask for the pixel.
178 Leaves the cursor address in lcdcurs.
179 Limits: 0 LE x LE 511, 0 LE y LE 63.
180
181 GLCdisp(dsp, crs, blk1, blk2, blk3)
182 short dsp, crs, blk1, blk2, blk3;
183
184 Sets the overall display, cursor and block status values.
185
186 GLCinit()
187
188 Initializes the GLC.
189
190 GLCplot(x, y, val)
191 unsigned x, y, val;
192
193 Plots a dot at x, y. The dot will be dark if val is non-zero.
194
195 GLCtext(row, col, s)
196 unsigned row, col;
197 char *s;
198
199 Sets the GLC cursor to ('row', 'col'), then writes the
200 character string pointed to by 's'.
201 Cursor must start and end on the same line.
202 No error checks are done.
203
204 GLCwrts(s)
205 char *s;
206
207 Writes the character string pointed to by 's' at the
208 current cursor position on the LCD display.
209 Cursor must start and end on the same line.
210 No error checks are done.
Note: See TracBrowser for help on using the repository browser.