source: buchla-68k/vlib/vobjfns.c@ 0170798

/*
   =============================================================================
        vobjfns.c -- VSDD object functions
        Version 23 -- 1988-01-29 -- D.N. Lynx Crowe
        (c) Copyright 1987,1988 -- D.N. Lynx Crowe

        SelObj(obj)
        int obj;

                Select 'obj' as the current working object.

        SetPri(obj, pri)
        int obj, pri;

                Display object 'obj' with priority 'pri'.

        SetObj(obj, type, bank, base, xpix, ypix, x0, y0, flags, pri)
        int obj, type, bank, xpix, ypix, x0, y0, flags, pri;
        unsigned int *base;

                Setup object 'obj' of type 'type' at 'base' in bank 'bank'
                with height 'ypix' and width 'xpix' at initial location
                'x0','y0', with flags 'flags'.  Assumes HRS EQ 1.
                If 'pri' >= 0, display the object at priority level 'pri'.
                Define a bitmap object if 'type' EQ 0, or a character object
                if 'type' NE 0.

        CpyObj(from, to, w, h, sw)
        unsigned int *from, *to;
        int w, h, sw;

                Copy a 'w'-word by 'h'-line object from 'from' to 'to' with
                a destination width of 'sw' words.
*/

/* 

*/

/*
        VIint() is located in viint.s but is mentioned here for completeness

        VIint()

                Vertical Interrupt handler.  Enables display of any object
                whose bit is set in vi_ctl.  Bit 0 = object 0, etc.

                SetPri() uses BIOS(B_SETV, 25, VIint) to set the interrupt
                vector and lets VIint() enable the object.  If vi_dis
                is set, SetPri() won't enable the interrupt or set the vector
                so that several objects can be started up at once.
   =============================================================================
*/

#include "ram.h"

int16_t         wsize;          /* object width calculated by SetObj() */
int16_t         vi_dis;         /* disable use of VIint */

uint16_t        vi_ctl;         /* object unblank control bits */

/* 

*/

/*
   =============================================================================
        SelObj(obj) -- Select 'obj' as the current working object.
   =============================================================================
*/

void SelObj(int16_t obj)
{
        register struct octent *op;
        register uint16_t newbank;

        op = &v_obtab[obj];

        newbank = ((op->obank & 0x0001) << 8) | ((op->obank & 0x0002) << 6);

        v_nobj = obj;
        v_curob = op;
        v_obpri = op->opri;

        if ((v_regs[5] & 0x0180) NE newbank)
                vbank(op->obank & 3);
}

/* 

*/

/*
   =============================================================================
        SetPri(obj, pri) -- Display object 'obj' with priority 'pri'.
        
                Blanks the object first, then sets the access table
                and unblanks the object via VIint().
   =============================================================================
*/

void SetPri(int16_t obj, int16_t pri)
{
        register struct octent *op;

        if (v_regs[5] & 0x0180)         /* point at the control bank */
                vbank(0);

        op = &v_obtab[obj];             /* point at the object table */
        op->opri = pri;                 /* set the priority */

        v_odtab[pri][0] = op->odtw0 | V_BLA;    /* start object as blanked */
        v_odtab[pri][1] = op->odtw1;
        v_odtab[pri][2] = ((int32_t)op->obase >> 1) & 0xFFFF;

        objon(pri, op->objy, op->ysize);        /* enable access table bits */

        if (vi_dis)                             /* don't unblank if vi_dis set */
                return;

        setipl(7);                              /* disable interrupts */

        vi_ctl |= (1 << pri);                   /* set unblank bit */

        if (*((int32_t *)0x000064) NE &VIint)   /* make sure VI vector is set */
                BIOS(B_SETV, 25, VIint);

        setipl(0);                              /* enable VI interrupt */
}

/* 

*/

/*
   =============================================================================
        SetObj(obj, type, bank, base, xpix, ypix, x0, y0, flags, pri)
        Setup an object, and optionally display it.  Assumes HRS EQ 1.
   =============================================================================
*/

void SetObj(int16_t obj, int16_t type, int16_t bank, int16_t xpix, int16_t ypix, int16_t x0, int16_t y0, int16_t flags, int16_t pri, uint16_t *base)
{
        register struct octent *op;

        if (v_regs[5] & 0x0180)         /* point at the control bank */
                vbank(0);

        op = &v_obtab[obj];

        v_curob = op;
        v_nobj = obj;
        v_obpri = pri;

        op->ysize = ypix;
        op->xsize = xpix;
        op->objx = x0;
        op->objy = y0;
        op->obase = base;
        op->opri = pri;
        op->obank = bank & 3;

/* 

*/
        if (type) {     /* character objects */

                op->odtw0 = (flags & 0xF9FF) | V_CTYPE;

                switch (V_RES3 & op->odtw0) {

                case V_RES0:

                        wsize = xpix / 128;
                        break;

                case V_RES1:

                        wsize = xpix / 48;
                        break;

                case V_RES2:

                        wsize = xpix / 64;
                        break;

                case V_RES3:

                        wsize = xpix / 96;
                        break;
                }

                if (V_FAD & op->odtw0)
                        wsize = wsize + (wsize << 1);

/* 

*/
        } else {        /* bitmap objects */

                op->odtw0 = (flags & 0x0E37) | (V_BTYPE | ((bank & 3) << 6));

                switch (V_RES3 & op->odtw0) {

                case V_RES0:
                case V_RES1:

                        wsize = 0;
                        break;

                case V_RES2:

                        wsize = xpix / 32;
                        break;

                case V_RES3:

                        wsize = xpix / 16;
                        break;
                }
        }

        op->odtw1 = ((x0 >> 1) & 0x03FF) | (0xFC00 & (wsize << 10));

        if (pri < 0)
                return;

        SetPri(obj, pri);
}

/* 

*/

/*
   =============================================================================
        CpyObj(from, to, w, h, sw)

        Copy a 'w'-word by 'h'-line object from 'from' to 'to' with
        a destination width of 'sw' words.  Assumes we're pointing at
        the correct bank.
   =============================================================================
*/

void CpyObj(uint16_t *from, uint16_t *to, uint16_t w, uint16_t h, uint16_t sw)
{
        register uint16_t *tp;
        register uint16_t i, j;

        for (i = h; i--; ) {

                tp = to;

                for (j = w; j--; )
                        *tp++ = *from++;

                to += sw;
        }
}